Highly efficient BIPV goes colourful

Highly efficient BIPV goes colourful

Advanced Colour Technologies Unlock New Design Freedom For BuildingIntegrated Photovoltaics

New developments in coloured, high-performance BIPV enable architects to integrate solar energy into façades more flexibly, supporting large-scale renewable deployment without compromising aesthetics.

Building-integrated photovoltaics (BIPV) are considered a key technology for the energy transition in buildings, and their installation is now picking up speed. According to the “Deutsche Energie-Agentur” (German Energy Agency – dena), more than 10 gigawatts of solar power generation capacity were added in Germany in 2023 and 2024. This is a success that needs to be built upon because, according to surveys by the Fraunhofer Institute for Solar Energy Systems, up to 1,000 gigawatt peak (GWp) could be installed on Germany’s available roof and façade surfaces; the PV needs in a completely renewable energy system would already be achieved at around 500 GWp. glasstec asked experts Prof.-Dr.-Ing. Ulrich Knaack (Technical Universities of Darmstadt and Delft) and Dr. Thomas Kroyer (Fraunhofer Institute for Solar Energy Systems – ISE) how BIPV can be deployed more often in the future and what new solutions are available.

Highly efficient BIPV goes colourful

Renewable energy is the most important source for rising electricity needs, including those of the heating and mobility sectors in transition, especially via wind energy and photovoltaics, not least due to their comparatively low generation costs. However, the by far greatest growth potential for photovoltaics lies in building skins which, with their large usable expanses, would make urban energy supply more sustainable when equipped with PV.

Solar building skins significantly reduce CO₂ emissions in the building sector, offer shading, avoid grid extension costs and generate sustainable added value locally. One reason BIPV is still too rarely considered for vertical installation could be the limited creative freedom traditionally associated with PV module design. Architectural glass with built-in PV cells, such as Sunplus BIPV or Pilkington solutions, has enabled pattern based designs for several years, but until now there have been hardly any colour design options for highly efficient BIPV modules.

Highly efficient BIPV goes colourful

“In my understanding, more possibilities to adapt the colour and dimensions of modules to the desired geometry and aesthetics of the building are needed for a stronger uptake of building-integrated photovoltaics especially in façades,” explains Prof. Dr.-Ing. Ulrich Knaack, Head of the Façade Structures department at TU Darmstadt and Head at the “Design of Construction” chair at TU Delft.

“Module aesthetics follow façade aesthetics. And vice versa: through colour-customisable modules architects can design the aesthetics of façades. We have to understand BIPV façade components like bricks, clinker bricks or design panels: here we can select from a wide variety of surfaces and now also sizes and then also use these in custom patterns – with a view to achieving a desired individuality.”

One major obstacle to colour customisation has so far been the lower efficiency of designed module glass compared to conventional black modules.

Highly efficient BIPV goes colourful_5

Coloured BIPV for designing façades

The Fraunhofer Institute for Solar Energy Systems ISE has been working on a solution for several years that has now reached market readiness for large volumes and any module dimension. Dr. Thomas Kroyer, a researcher at Fraunhofer ISE, developed the patented “MorphoColor” technology with his team. Unlike colour pigments or coloured films, some of which strongly shade the module, the institute produces the desired colour using an interference layer that allows precise optical reflection of individual wavelengths to generate intense colour. For the remaining large spectrum of sunlight, the glass remains transparent and energy loss remains low.

“There are many well suited surfaces on roofs and façades for photovoltaics to be integrated in a meaningful way. With our solution we give architects the freedom to use PV modules as design features. Alternatively, the PV functionality can also be concealed completely. In most cases, you can still see up close that these are PV modules but seen from a few metres away you no longer notice the difference between these and normal façade panels.

Highly efficient BIPV goes colourful

Depending on the colour tint, coloured PV modules with MorphoColor coating achieve 90–96% of the efficiency of comparable black modules:

“With conventional solar modules the majority of the energy is converted into power from the incident photons of the long-wave red light. The short wave blue light, by contrast, is only used to a lesser extent. This is why the power loss is lower when blue light is reflected rather than red light. A module with a blue cover glass therefore has a slightly better efficiency rate (96% of the performance of a black module) than a red one (94%).

Highly efficient BIPV goes colourful

Coloured photovoltaics also open up new possibilities in areas where they might not be expected, such as the protection of listed buildings and ensembles. Kroyer adds: “PV installation on the roofs of such listed buildings had been difficult until now. However, red modules blend very well with the cityscape for typically red roofing.” To enable large-format cover glass and extensive projects, Fraunhofer ISE has brought the technology to market readiness in cooperation with licensee AGC Plasma. The company applies the coatings in Lauenförde using magnetron sputtering to achieve homogeneous colours and high angular stability, and was also a funding partner alongside the Institute and photovoltaic module producer Axsun (near Ulm, Germany). The development was subsidised by the German Federal Ministry for Economic Affairs and Climate Action as part of th “PVHide” project.

Highly efficient BIPV goes colourful

The most recent and, to date, largest MorphoColor project is the PV system on the roof of the north stand of Hamburg’s Millerntor stadium in rainbow colours, with LichtBlick SE acting as lead planner.

glasstec 2026 will take place in Düsseldorf from 20 to 23 October 2026 and will once again serve as the central global trade fair for discussing future topics in the glass industry, including Building-Integrated Photovoltaics (BIPV).

Highly efficient BIPV goes colourful

About the author

Marc Everling studied media education at the Technical University of Brunswick and has worked as a communication and marketing specialist in the glass industry for more than 20 years. In 2021, he founded a networking agency specialising in communications consulting and press liaison for companies and associations working sustainably in support of the ecological transformation of the construction sector.

About glasstec

glasstec is the world-leading trade fair for glass production, finishing and products, held every two years at the Düsseldorf Exhibition Centre. From 20 to 23 October 2026, it will bring together international decisionmakers, market leaders and experts from across the glass industry.

– Angela Meier-Buntenbroich
Email: [email protected]

– Theresa Oswald
Email: [email protected]

Website: www.glasstec.de